wholesale motorcycle hid projector headlights

hid xenon ballast

1. hid high quality
2.hid  Low Defective < 2%
3. hid Best price, quality and service
4. hot hid kits

motorcycle hid projector headlights

hid canbus ballast

1. high quality
2. Low Defective rate less than 2%
3. Best price, quality and service
4. 15 months warranty

Technical details:

HID Xenon Lamp Descriptions:

1. HID Xenon Bulb Voltage: 12V, 24V

2. HID Xenon Lamp Wattage: 35W, 50W/55W,75W

3. HID Bulb Models:

HID Single beam bulb: H1,H3,H4,H7,H8,H9,H10,H11,H13(9008),H16(5202),9004(HB1),

9005(HB3),9006(HB4),9007(HB5),880,881,D1S/C,D1R,D2S/C,D2R,D3S/C,D4S/C,D4R;

HID Fexible Lamp(High/Low,Hi/Lo, Bi-xenon): H4-3(Hi/Lo),H13-3(Hi/Lo),9004-3(Hi/Lo),

9007-3(Hi/Lo);

HID Xenon+Halogen Lamp: H4-2, H13-2, 9004-2, 9007-2;

HID Double/Dual/Bi-Xenon Lamp(Xenon+Xenon): H4-4, H13-4, 9004-4, 9007-4;

Advantage of HID:

1. Great Visibility and Road Safety

2. Waterproof, circuit protection

3. Easy installation

4. Wide color temperature

The factory quality control process before shipment:
1) 6 hours continuous working aging test.
2) Connection circuit protection test.
3) Short circuit protection test.
4) Lack of voltage protection test.
5) Over voltage protection test.
6) Flash light concussion test.
7) Quakeproof capability test.
8) Cold warm boot test.
9) Polarity protection test.
10) EMC anti-jamming test.

Constitute:

Basic fittings:

2pcs of HID xenon bulb (as per your need, all bulb type and color temperatures available)

2pcs of HID xenon ballast (DC/AC, 12V/24V, 35W/50W/70W available)

Mounting brackets

Installation instruction

All necessary accessories

Installation:

1, Please open the hood and take off the assembly of the headlights on the two sides (left and right).In the case of enough room for installation, the headlights may not be taken down.

2, Open up the back cap of the assembly of headlights and take out the original bulbs.

3, Drill a hole in the middle of the back cap with a 25mm cutter.

4, Take down the plastic cover surrounding the HID head lamp.

5, Put the HID head lamp into the headlights.

6, First plug the bulbs wiring harness into the rubber base and then put it into the back cap of assembly. After that, please shut the headlight shield tightly.

Safety Instruction:

1, Please wait for the entire cool-down of the car lighting and engine for the sake of safety in installation.

2, Before the installation, please confirm that the gear is at ‘N’ or ‘P’ and insure that the switch is off in installation.

3, Be carful to avoid scald, especially in turning on/off the car lighting. Be careful to avoid beating and cutting bulbs, not to touch bulbs with fingers, which will bring blot.

4, Be careful to examine the connection of the contactor, ports and voltaic wire. False connection will bring on lighting problems.

5, Please let the end of bulb not touch the interior light shield of the headlight assembly when adjusting the bulb.

6, Please drill a hole of 25mm in the back cap of resin or rubber on the headlight. In connection the bulb and the step-up transformer, do not connect the wrong electrode.

7, In putting through the power supply of a step-up transformer, do not connect the wrong electrode.

Transaction Terms:

Delivery Details: