HID xenon lamp system installation tips
 
 
HID Headlamps system please read the manual carefully!
HID device Step
Step 1: Let the car engine to cool at least 10 minutes, when the device is to avoid the water tank and the engine burns;
Step 2: Remove the HID headlights, HID headlamps with the ballast (Ballast) divided into two groups, in order to gradually set of devices;
Step 3: The headlight power connector, waterproof rubber cover and remove the old headlight;
Step 4: HID headlights on the headlamp unit holder;
Step 5: Determine the correct device is fixed headlights, headlights to prevent deformation of the base;
Step 6: Determine the waterproof rubber cover installed;
Step 7: Fixed Ballast (Ballast) and tie the line group;
Step 8: Ballast (Ballast) set of power supply input terminal and car headlights terminal binding;
Step 9: The HID headlights harness with the ballast (Ballast) harness connector;
Step 10: Check all devices steps to determine the positive and negative device is correct, you can open the headlights;
Step 11: Check the headlights illuminated height and distance, and make appropriate adjustments to avoid glare is too strong;
Step 12: Installation is complete, enjoy night driving fun!
Safety Precautions on (must read before use)
1, HID system will produce a high voltage (about 23KV), please note that when the device is fully (Demolition). Ago device operation, please check the product [Ballast Group (Ballast), headlights (Bulb Kit) state, such as wire damage, leakage glue, terminal damage, leakage of high-voltage wire, please abort the job immediately.
2, HID headlights and Ballast (Ballast), connecting terminals, please do not arbitrarily change. After the high voltage generated due to the lighting, the risk of leakage caused by the body.
3, headlights (Headlight) or when the lights just after lights out, hands or skin Do not touch, do not directly hit the water when washing. Because headlights (Headlight) will produce high temperatures may cause burns.
* When washing or will touch near the headlight (Headlight) site, please fully cool before operation.
4, be sure to check the position of the front light axis (Beam axis) whether appropriate and, where appropriate adjustments. This system is generally due to the brightness of greater than halogen headlights (Halogen bulb), such as the optical axis (Beam axis) does not regulate, or deliberately axis (Beam axis) up, may lead to an accident, be sure to check and adjust.
5, do not look directly at the light when lit. So can cause eye pain or vision impaired, do not look directly at lights near.
6, note that (6.2 ~ 21V) and the positive and negative electrode device.
7, please use the wiring group when the device is HID.
8, when the device, please pay special attention to the positive and negative electrodes are grounded power pole, as the car for special specifications, the positive electrode is grounded, the ballast (Ballast) and body contact may cause flashover, when such vehicles device to be added equipped with wiring group diodes, otherwise dangerous will happen.
9, device HID headlights when:
1) Please note that the power cord for truck-mounted safety standard UL1015 (TEW, singlet) of the power cord.
2), UL1015, TEW, AWG24 or the diameter is too small, use the wiring group, in order to avoid empty wave damage electrical equipment.
10, when the device HID headlights, turn off all power to the unit after completion of all the normal lighting, before opening the power supply to avoid surge impact Ballast (Ballast).
11, HID headlights with ordinary car headlights lighting in different ways, when the switch is "open", HID Ballast (Ballast) will continue to automatically and continuously lighting lit up. If not immediately turn lights, please wait for two minutes, the system will automatically illuminate. If this does not light, should be closed immediately switch to the auto repair shop to check.
12, please do not start the engine at the same time light, in order to protect and extend the life of HID lamps.
13, before the device to test HID lamps, use DC-12V battery test, in order to avoid non-standard specifications of the power supply is damaged HID ballast (Ballast).
14, please pay special attention Ballast (Ballast) and high voltage box, device location, please keep away, do not close the following locations, in order to avoid Ballast (Ballast) HID lights off due to overheating, increasing the risk of driving at night:
1), spark plugs and spark plug lines.
2), the electronic circuit carburetor.
3), tank and engine heat.
4) Select the ventilation and cooling good position.
5), to avoid stagnant water, leak location.
15, if the two HID lamps start, there has delays, please swap HID lamps, if the delay remains the same, said the imbalance in power systems, please add the assembly line groups.
Note the use of:
1, parking (for example, traffic lights, etc.), do not frequently lights on / off.
Repeated lights on / off headlights will loss electrodes inside, resulting in shortening the life of the system or not lighting problems. [Note] headlight switch (Headlight switch) turned on and off (on / off) of the interval is too short, and sometimes can not be lit.
2, the following is a result of the use of the environment or conditions caused by, not because the product is bad.
1) When the cold weather (below 0 degrees Celsius) lights slower than normal start time (1 to 2 seconds), not a malfunction.
3, does not occur in the use of lights, please follow these simple steps to check.
1) Make the vehicle to a safe location as soon as possible;
2) The headlight switch (Headlight switch) to turn off the lights (off) state, over a few seconds after the lights (on);
3) When the above situation has not improved after the operation, turn off all lighting switch (Lighting switches) (excluding hazard lights (Hazard) lights out for about 10 to 20 minutes, then lights up.
* After the above as restoration examination was normal, said ballast (Ballast) in the microcomputer memory (CPU) engine cooling adverse effects by. Continue with no problems. If the situation does not improve, or the occurrence of other problems, please have the vehicle to the nearest parking equipment location as soon as possible, and with the purchase or sale of the device stores contact, seek help solve the problem.
4, if found inconsistent with the two headlights lit time or only a single lamp is lit, a circuit system power imbalance, please add the assembly line groups.
5, in the summer, when the long night climbing and highway driving, the engine can overheat, if found headlights suddenly go out, do not panic! This phenomenon indicates HID Ballast (Ballast) device location inappropriate cause overheating, please turn off the power immediately headlights, driving the car to the roadside and after cooling, you can automatically return to normal, and go to an auto repair shop to adjust the device position .
6, headlights rupture or leakage phenomenon, rainy absolute prohibition of lights, to avoid danger.
7, if it found it impossible to close the phenomenon, said wiring error please correct immediately.
8, headlight switch "turned on," If you can not light up when the HID lamp immediately, do not frequently lights on / off, patiently waiting for Ballast (Ballast) CPU system will automatically lighting, continued to light up so far. If not lit within 1 to 5 minutes, go to an auto repair shop to check, or cause Ballast (Ballast) burned, improper This operation is not included in the product warranty.
9, for any loss due to the use of this product malfunction caused damage, including loss of profits, loss of property, casualty V-WIN companies and authorized service provider does not bear any responsibility.
Line group device program:
Normal device program
① pick Ballast (Ballast) Power
② contact body (negative)
③ connect the battery (positive)
④ Power Control Connector
* If the car is the anode body
① opposite Ballast (Ballast) positive and negative electrode wiring
② take the body (positive)
③ connect the battery (negative)
④ opposite power control wiring

Web:  ..........com， ..........en..........., ..........en...........