HID xenon lamp solutions to common problems
 
 
HID lights installed FAQs 1.HID safety performance? A: Because our products <Ballasts> has a strict anti-AIDS electrical circuits and various abnormal conditions interfere with the automatic protection features, so products supporting electronic ballast during any abnormal state will automatically cut off the circuit. Not produce any danger to cars and people, you can be assured. 2.HID lights installed for those models? A: Since we launched adaptation H1, H3, H4, H7, 9005,9006,9007, such as xenon lamps. So almost all of the models can be applied. 3.HID easy installation? A: Actually HID installation is the original car headlamp halogen bulb removed and replaced with the same type of lamp xenon bulb and ballast installation, while the dust cover on the drilling leads to harness and installation of relay line group, the installation is very easy, but for the sake of safety recommendations by professional automotive electrician. 4 Q. HID bulbs waterproof it? A: Our HID bulbs and electronic ballasts have been soaked in water experiments, so HID lamps and ballasts are waterproof, customers can be assured. 5 Q. There are many models headlight cover is sealed, how should lead to the harness? A: If the cover is sealed with a 25MM reamer can be punched in the back cover, and then sealed waterproof cap cover fit. 6 Q. HID installation need to replace the fuse? A: Because the HID light bulb moment will produce 2,3 million volts and high current, the original car's fuse is generally 10A, 15-20A proposal to change a fuse, but does not require the installation of relay line group after replacing the fuse . 7 Q. HID Electronic Ballast 12V input correct. Will burn the negative reversed ballast? A: No, if the power of positive and negative reversed, the protection circuit will automatically disconnect the power ballast, the ballast will not burn, but not long energized. 8 Q. HID lights installed, whether the removal of all models have large shade before? A: No, if there is sufficient space for installation, removal may not be the entire headlight down. 9 Q. How to identify good and bad ballast? A: First, in accordance with international standards, lit one second to reach 20% within 4 seconds to reach more than 80% brightness is good ballast, and instantly reach 80% brightness or four seconds up to standard brightness ballast is poor quality. Second, the start-up mode, start ballast is divided into two, one cold start, when the ballast and bulb lights are in a cooled state; Second hot start, is the ballast and bulbs are in the normal operating temperature type opening light, in this state the switching operation is repeated in succession do, good quality normal ballast lights, some lighting ballast appears abnormal, there will be a light of a lamp does not light phenomenon. Must cut off the power on again. The latter is obviously poor quality. Third, the current market is divided into two kinds of ballast, split and integrated; split on the installation concerned is not easy, while technically belong to the early products. 10. Bulbs currently on the market have 4300K, 5000K, 6000K, 8000K, 10000K 12000K even choose which is better? A: Usually People have a misconception higher the temperature, the higher the brightness. In fact, the brightness of the unit is the lumen (M), 4300K ​​is white with a little yellow; 5000K close to natural light; 6000K white with a bit of blue; 8000K is bluish; 10000K is blue; 12000K already was blue. And we know that higher the temperature, the lower the lumens of light, the fog, rain penetration worse. General Use 4300K ​​~ 6000K best. 11 Q. There are many cars on the market today use H4 bulbs, many people reflect the distance light HID lamps are not used, is that right? A: Yes, because of the distance of H4 HID lamps are the following issues: one, the distance light are retractable, generally used motor, hydraulic, pneumatic and magnetic acting, and this time the telescopic HID very easy to be stuck, a few months later became a single lamp. Second, telescopic HID lamp base very long, destructive original headlight group is larger, but also more difficult to install, but also appeared lamps water phenomenon. Three, telescopic HID lamps may need to destroy the original factory mask, which can lead to optical like the present entry. Fourth, double HID lamps makes the car more optical greatly increased. As we all know, is based on the original halogen headlight design, light from tungsten halogen light very close proximity, while the dual HID lamps on the market today can not do this. Makes this light beam can not meet the needs of lamps with light, out of the light only rotation, causing fatal injuries to other vehicles, but also affect their safety. In addition, the structure of this kind of bulb it is easy to determine the leakage, ignition, light ballasts will burn, heavy on the people, there is a serious safety hazard car. 12 Q. How do I adjust the light level? (This is for reference only; not fully operate here) Answer: First, align the front side of the wall stop, a distance of about 10 meters, pay attention not want to have any positive skew, the body must maintain a level of precision possible in order , you can draw with chalk marks, note should be in a normal vehicle load standards that no extra load, the final commissioning: a: the lights turn on, which is projected on the wall of the aperture correction basis. The center of the two lights, the car from the front axle should be equidistant from its projection on the wall, or else be adjusted according to the third step; the right to the ground from the center of the lamp should be equidistant from its projection on the wall, the left light this distance will have higher than its projection 10CM. Second, adjusted to a straight line, move the left headlight to be absolutely direct, whereas the right headlights slightly to the right, because the right you can see very clearly, foggy weather is particularly effective. Third, the cover easy to adjust a headlight, headlight cover one with a thick cloth, so you can change a headlight beam incident on the wall for effective regulation, with two screwdrivers debugging, a adjust the height of the beam, and the other is used to adjust the width of the beam. 13 Q. HID lights installed line group must install it? What are the benefits of retrofitting line group? Answer: Not necessarily all of the cars had to install line group, if enough of the original car's power cord crude would not install line group; contrary necessary to install line group. Double loop and double circuit line group car safety device to protect electrical circuits, connecting terminals to prevent corrosion poor contact occurs, large current capacity of the wire is not connected to the fuse wire can guarantee, allows customers ease of use. 14 Q. H4 (high / low) lights and other lights installed models What's the difference? A: Because the use of only one car lamp H4 headlight lamps. And the original halogen is the distance light is integrated. So they are three-wire power input (ie, a positive share, two separate negative). And my company is using an H4 HID lamp, installed a HID lamps, an ordinary halogen lamps, so the installation should pay attention to ordinary halogen lamps. Ordinary halogen or 12V DC power supply, while HID lamp ballast must complete the final connection HID lamp power lines. Be sure to install the lamp when the power control line distance to distinguish, not to ordinary halogen HID lamps and connected to the same input power. 15 Q. How do I install waterproof hat? Should pay attention to what the problem is? Answer: HID lights flashing installation is divided into two: one is the original lamp power cord in the fixture, such models can be installed without the power cord leads from waterproof hat and playing with the headlight lamps cover reamer hole, the diameter of the reamer is generally 25MM, the operation should be subject to the inner diameter of the waterproof cap. Another is the original power in the lamp lights outside, mostly 9000 series bulbs so, when such models would facilitate installation and more, directly to the power supply and ballast (or line group of signal lines) to connect to, and then the water cap and lighting match phase. Thank you for using our products, if you have other questions or suggestions, you may also be that you fill in the attached document, fax or EMAIL questions or comments on our products to us and we will answer you as soon as possible.